问题 - 道道学堂问答

会计Accounting

经济Economics

金融Finance

领导力与组织管理Leadership and Organization Management

土木工程Civil Engineering

计算机类Computing

其他 All Others

Please solve it APDL and your solutions should be uniqe but notcopy right.If you solved this i want you do it again :)

匿名用户 2021-12-01 18:49 机械工程Mechanical Engineering

Please solve it APDL and your solutions should be uniqe but notcopy right.If you solved this i want you do it again :)0.... 查看全部

2021-12-01 18:49
0
赞同
1
回答

The square bar shown (Figure 1) is 60 mm thick and 6 m long and is fixed supported at both ends. A load directed leftward is applied at point C, as shown L2 = 5.28 m from the left end. The modulus of elasticity is E = 100 GPa .if point C moves 8 = 0.075 m

匿名用户 2021-12-01 18:49 机械工程Mechanical Engineering

The square bar shown (Figure 1) is 60 mm thick and 6 m long and is fixed supported at both ends. A load directed leftwar... 查看全部

2021-12-01 18:49
0
赞同
1
回答

Problem 4.62 6 of 9 The rigid bar is supported by the two short white spruce wooden posts and a spring 50 kN/m А c R 1 m m 1 m Part A If each of the posts has an unloaded length of 1 m and a cross-sectional area of 850 mmand the spring has a stiffness of

匿名用户 2021-12-01 18:49 机械工程Mechanical Engineering

Problem 4.62 6 of 9 The rigid bar is supported by the two short white spruce wooden posts and a spring 50 kN/m А c R 1 m... 查看全部

2021-12-01 18:49
0
赞同
1
回答

Four masses A, B, C and D are attached to a shaft and revolve in the same plane. The masses are 100 kg, 150 kg, 120 kg and 130 kg respectively and their radii of rotations are 225 mm, 175 mm, 250 mm and 300 mm. The angular position of the masses B, C and

匿名用户 2021-12-01 18:49 机械工程Mechanical Engineering

Four masses A, B, C and D are attached to a shaft and revolve in the same plane. The masses are 100 kg, 150 kg, 120 kg a... 查看全部

2021-12-01 18:49
0
赞同
1
回答

Part A - Force with a known deflection Leaming Goal: To solve for forces in statically indeterminate bars with axial loads. When the number of reaction forces is greater than the number of equilibrium equations, the system is statically indeterminate. Sol

匿名用户 2021-12-01 18:49 机械工程Mechanical Engineering

Part A - Force with a known deflection Leaming Goal: To solve for forces in statically indeterminate bars with axial loa... 查看全部

2021-12-01 18:49
0
赞同
1
回答

Consider the planar PR manipulator shown here: Y3 X3 L1 21 Y2 X2 02 - L2 X1 di zo Хо (a) Find the origin of frame {3} expressed in terms of frame {0}, that is 'P3org. Tip: you can derive this geometrically, if you want to avoid going through DH p

匿名用户 2021-12-01 18:49 机械工程Mechanical Engineering

Consider the planar PR manipulator shown here: Y3 X3 L1 21 Y2 X2 02 - L2 X1 di zo Хо (a) Find the origin of frame {3} ex... 查看全部

2021-12-01 18:49
0
赞同
1
回答

Homework The flat bar shown in figure, is 10 mm thick and is pulled by a force P producing a total change in length of 0.2 mm. Determine the maximum stress developed in the bar. Take E= 200 GPa. Filler with stress concentration factor 2.5 Hole with stress

匿名用户 2021-12-01 18:49 机械工程Mechanical Engineering

Homework The flat bar shown in figure, is 10 mm thick and is pulled by a force P producing a total change in length of 0... 查看全部

2021-12-01 18:49
0
赞同
1
回答

Learning Goal: To Use The Principle Of Superposition To Determine The Total Deflection In A Cylindrical Rod Due To A Static Loading A Steel Rod (E = 200 GPa) Is Subjected To The Load Shown, Where P = 2525 EN. A Gap A = 2.00 Mm Exists Before The Load Is Ap

匿名用户 2021-12-01 18:49 机械工程Mechanical Engineering

Learning Goal: To use the principle of superposition to determine the total deflection in a cylindrical rod due to a sta... 查看全部

2021-12-01 18:49
0
赞同
1
回答

A set is set in front of a stream, a 12 m head is obtained and asmall turbine is operated, and it can be directly from the turbineshaft.By means of a pump that is driven, further cultivation areaslocated 15 m above elevationirrigation is planned. The flow

匿名用户 2021-12-01 18:49 机械工程Mechanical Engineering

A set is set in front of a stream, a 12 m head is obtained and asmall turbine is operated, and it can be directly from t... 查看全部

2021-12-01 18:49
0
赞同
1
回答

Problem 3 Multi-DOF Response To A Cyclic Input (40pts) In The Previous Assignment, We Modeled A Passive Quarter Suspension Model. Now We Add A Controller To Make The Suspesion System Active. As Shown. 1 Se Mc Suspension System U Kožbe + I Mw 22 Kw Ibw Whe

匿名用户 2021-12-01 18:49 机械工程Mechanical Engineering

Problem 3 Multi-DOF Response to a Cyclic Input (40pts) In the previous assignment, we modeled a passive quarter suspensi... 查看全部

2021-12-01 18:49
0
赞同
1
回答